Welcome to the Shaarp Mind Forum.






+ Reply to Thread + Post New Thread
Results 1 to 13 of 13
  1. #1
    Member
    Join Date
    Apr 2012
    Posts
    566

     

    states of the phone is dead ...


    flashing Along with atf *


    flashing is ok but one error is show (lcd test failed )


    /



    VBATT Powering Down <<<<

    VBATT Powering Up >>>>

    SET VCCIO Level Done

    SET BSI Load Done


    Booting Phone...

    CPU ID Response: A200341100

    CPU Type: XG110 2.1B

    Phone Booted at after First attempt...


    ************************************************** ****

    TIME STARTS HERE

    ************************************************** ****



    Sending PBL 19456 bytes...

    PBL Successfully Sent...


    Sending SBL 65024 bytes...

    SBL Successfully Sent...


    Flash Chip Manufacturer: STMicroelectronics

    Flash Chip Type: M58WR064 64 Mbit (4Mb x 16) NOR

    Extended Information: Multiple Bank / Burst / 1.8v


    Processing Image File: C:Program FilesNokiaPhoenixProductsRM-769
    m769_007.200


    FIRMWARE Image Found...

    Number of Sections: 03

    FIRMWARE Certificate Block Sent Successfully...

    Processing Section 01 of 03

    FIRMWARE Erase Block: 0x00000000~0x0001FFFE

    Start Erasing...

    Erasing kindly Wait...

    Block Erase Done...

    Preparing Data Blocks...

    Data Size: 24576 bytes

    Data Checksum: F5BE

    Uploading Data Blocks to phone...

    FIRMWARE Data Blocks uploaded to phone...

    Processing Section 02 of 03

    FIRMWARE Erase Block: 0x00800000~0x00BFFFFE

    Start Erasing...

    Erasing kindly Wait...

    Block Erase Done...

    Preparing Data Blocks...

    Data Size: 4128768 bytes

    Data Checksum: BFB7

    Uploading Data Blocks to phone...

    FIRMWARE Data Blocks uploaded to phone...

    Processing Section 03 of 03

    FIRMWARE Erase Block: 0x00C5D000~0x00E5FFFE

    Start Erasing...

    Erasing kindly Wait...

    Block Erase Done...

    Preparing Data Blocks...

    Data Size: 1697536 bytes

    Data Checksum: 2B05

    Uploading Data Blocks to phone...

    FIRMWARE Data Blocks uploaded to phone...

    Start Data Verification... (kindly wait)

    Data Verification Successful...



    Processing Image File: C:Program FilesNokiaPhoenixProductsRM-769
    m769_007.20mh


    PPM Image Found...

    Number of Sections: 01

    PPM Certificate Block Sent Successfully...

    Processing Section 01 of 01

    PPM Erase Block: 0x00100000~0x0061813E

    Start Erasing...

    Erasing kindly Wait...

    Block Erase Done...

    Preparing Data Blocks...

    Data Size: 5341504 bytes

    Data Checksum: 47D8

    Uploading Data Blocks to phone...

    PPM Data Blocks uploaded to phone...

    Start Data Verification... (kindly wait)

    Data Verification Successful...



    Processing Image File: C:Program FilesNokiaPhoenixProductsRM-769
    m7690_nai07.20mh_nlt


    CONTENT Image Found...

    Number of Sections: 01

    CONTENT Certificate Block Sent Successfully...

    Processing Section 01 of 01

    CONTENT Erase Block: 0x00E60000~0x00F49FFE

    Start Erasing...

    Erasing kindly Wait...

    Block Erase Done...

    Preparing Data Blocks...

    Data Size: 958464 bytes

    Data Checksum: BB37

    Uploading Data Blocks to phone...

    CONTENT Data Blocks uploaded to phone...

    Start Data Verification... (kindly wait)

    Data Verification Successful...



    Exit Flash Mode Done...

    Time Elapse : 00:04:32


    ************************************************** ****

    You must Factory Reset the phone to enable the

    ringtones and other customized settings to work

    ************************************************** ****



    Waiting For Phone to go Online...


    5* 4* 3* 2* 1...

    MCU: V 07.20 30-03-12 RM-769 (c) Nokia

    IMEI: 353654055460122

    Product Serial Number: 3D65DAFBI

    Product Code : 059J2D0

    Module Code : 0204874

    Basic Production Code: 059P5G1

    PPM SW Version : V 07.20 30-03-12 RM-769 (c) Nokia MH

    ADSP Version : p+V 07.20
    30-03-12
    RM-769
    (c) NMP
    mh_nlt

    MCU SW Version : V 07.20 30-03-12 RM-769 (c) Nokia

    HW Version : 3000

    UEM Version : 1328

    UPP Version : 8850

    LCD Version : UNKWN: IDs: 00:00:00

    ********** SIMLOCK INFO **********

    CONFIG_DATA : 0010100000000000

    PROFILE_BITS : 0000000000040002

    ASIC : 11

    PROVIDER : Default Test Operator


    Block [1] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [2] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [3] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [4] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [5] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [6] 1:Open 2:Open 3:Open 4:Open 5:Open

    Block [7] 1:Open 2:Open 3:Open 4:Open 5:Open

    ST_LCD_TEST : FAILED


    Phone Cannot Enter Normal Mode if LCD

    is Damaged or LCD is not Properly

    Connected to the Main PCB



    FACTORY SET TO : Full Factory Set

    OK

    FACTORY SET TO : User Data

    OK

    FACTORY SET TO : Leave Factory

    OK

    FACTORY SET TO : Service Center

    OK

    FACTORY SET TO : Software Upgrade

    OK

    FACTORY SET TO : Production Tune

    OK


    apply this jumber.. 100% working.....


    /


    /



    phone is on condeshion.....

    /

  2. #2
    Member
    Join Date
    Apr 2012
    Posts
    1,843

     
    Good info dear thinkssssssssssssss

  3. #3
    Member
    Join Date
    Apr 2012
    Posts
    1,901

     
    br old solution ...... any new solution th*x.........

  4. #4
    Member
    Join Date
    Apr 2012
    Posts
    1,901

     
    Quote:

    biniesh_08 [Only registered and activated users can see links. ]
    br old solution ...... any new solution th*x.........


    1616* 5030 *1662 etc..... pcb are different to 100 *101 because its new solution......

  5. #5
    Member
    Join Date
    Apr 2012
    Posts
    1,957

     
    thank u brotherrrrrrrrrrrrrrrrrrr

  6. #6
    Member
    Join Date
    Apr 2012
    Posts
    1,908

     
    Nic info...................bro

  7. #7
    Member
    Join Date
    Apr 2012
    Posts
    1,857

     
    nice sharing brooooooo

    than**x alot

  8. #8
    Member
    Join Date
    Apr 2012
    Posts
    1,916

     
    My pictures will not show me what is the problem?

  9. #9
    Member
    Join Date
    Apr 2012
    Posts
    1,916

     
    bro very very ooooooooooooooooooooooold

  10. #10
    Member
    Join Date
    Apr 2012
    Posts
    1,922

     
    Quote:

    kathirmobiles [Only registered and activated users can see links. ]
    bro very very ooooooooooooooooooooooold



    yes its old solution but i am asking to read this post ...


    this post nothing to use fore you... you can note read it


    many other people like this post i am vary happy to this ..


    because (1616* 5030 *1662 etc..... pcb are different to 100 *101)


    i am testing 2 mobile then post it .......


    any post you can read on time you will note use unknown camants are post it ok............

  11. #11
    Member
    Join Date
    Apr 2012
    Posts
    1,922

     
    thank you sir keep it up.... nice post

  12. #12
    Member
    Join Date
    Apr 2012
    Posts
    1,995

     
    thankyouuuuuuuuuuuuuuuuuuuu

  13. #13
    Member
    Join Date
    Apr 2012
    Posts
    1,923

     
    Quote:

    kathirmobiles [Only registered and activated users can see links. ]
    bro very very ooooooooooooooooooooooold


    i am search ur all comments and u say this solutions is old. i know u have sme experience bt u dont know how to respect people or their work.

    lol i know u r a sadist or jealous


    .bcoz if u know this is an old solutions then shut ur *****.suppose theire are so many peoples have no idea abt it.ok.if u think ur good then keep ur ***** silent ok.if u r a human just respect smeone work.you idiot going to continue this (comment something like this) then people not post their

    solutions to this forum ok u idiot.if u r a jenious then support people ok u dam dash


 

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

     

Similar Threads

  1. Replies: 0
    Last Post: 03-16-2013, 01:51 PM
  2. Replies: 14
    Last Post: 03-16-2013, 07:34 AM
  3. Replies: 14
    Last Post: 03-16-2013, 06:43 AM
  4. Replies: 0
    Last Post: 03-16-2013, 04:15 AM
  5. Replies: 14
    Last Post: 05-21-2012, 05:47 AM

Tags for this Thread